Get Prepared for Your NSE7_SDW-7.2 Exam With Actual 99 Questions

Valid NSE7_SDW-7.2 Test Answers Full-length Practice Certification Exams

NEW QUESTION # 27
Refer to the exhibit.

Which two statements about the IPsec VPN configuration and the status of the IPsec VPN tunnel are true?
(Choose two.)

• A. FortiGate does not install IPsec static routes for remote protected networks in the routing table. Most Voted
• B. The phase 1 configuration supports the network-overlay setting. Most Voted
• C. FortiGate facilitated the negotiation of the T_INET_1_0_0 ADVPN shortcut over T_INET_1_0.
• D. Dead peer detection is disabled.

Answer: A,C

NEW QUESTION # 28
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows the source NAT (SNAT) global setting and exhibit B shows the routing table on FortiGate.
Based on the exhibits, which two actions does FortiGate perform on existing sessions established over port2, if the administrator increases the static route priority on port2 to 20? (Choose two.)

• A. FortiGate continues routing the sessions with no SNAT, over port2.
• B. FortiGate updates the gateway information of the sessions with SNAT so that they use port1 instead of port2.
• C. FortiGate performs a route lookup for the original traffic only.
• D. FortiGate flags the sessions as dirty.

Answer: A,B

NEW QUESTION # 29
Refer to the exhibits.
Exhibit A -

Exhibit B -

Exhibit A shows the SD-WAN performance SLA and exhibit B shows the SD-WAN member status, the routing table, and the performance SLA status.
If port2 is detected dead by FortiGate, what is the expected behavior?

• A. FortiGate removes all static routes for port2.
• B. Host 8.8.8.8 is reachable through port1 and port2.
• C. Port2 becomes alive after three successful probes are detected.
• D. The administrator manually restores the static routes for port2, if port2 becomes alive.

Answer: A

Explanation:
This is due to Update static route is enable which removes the static route entry referencing the interface if the interface is dead

NEW QUESTION # 30
Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured packet loss will make T_INET_1_0 the new preferred member?

• A. When T_INET_1_0 has 4% packet loss.
• B. When T_INET_0_0 has 4% packet loss.
• C. When T_INET_0_0 has 12% packet loss.
• D. When all three members have the same packet loss.

Answer: A

NEW QUESTION # 31
Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured packet loss will make T_INET_1_0 the new preferred member?

• A. When T_INET_1_0 has 4% packet loss.
• B. When T_INET_0_0 has 4% packet loss.
• C. When T_INET_0_0 has 12% packet loss.
• D. When all three members have the same packet loss.

Answer: D

NEW QUESTION # 32
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows an SD-WAN event log and exhibit B shows the member status and the SD-WAN rule configuration.
Based on the exhibits, which two statements are correct? (Choose two.)

• A. FortiGate updated the outgoing interface list on the rule so it prefers port2.
• B. Port2 has the highest member priority.
• C. SD-WAN rule ID 1 is set to lowest cost (SLA) mode.
• D. Port2 has a lower latency than port1.

Answer: A,D

NEW QUESTION # 33
The administrator uses the FortiManager SD-WAN overlay template to prepare an SD-WAN deployment. With information provided through the SD-WAN overlay template wizard, FortiManager creates templates ready to install on spoke and hub devices.
Select three templates created by the SD-WAN overlay template for a spoke device. (Choose three.)

• A. System template
• B. BGP template
• C. Overlay template
• D. dIPsec tunnel template
• E. CLI template

Answer: A,C,D

Explanation:
In a FortiManager SD-WAN overlay template configuration for a spoke device, the system template (A) is created to provide basic device settings. The IPsec tunnel template (C) is generated to establish secure tunnels between the spoke and the hub devices. Lastly, the overlay template (E) is configured to specify the overlay network settings, which often include the SD-WAN rules and performance SLAs.

NEW QUESTION # 34
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows an SD-WAN event log and exhibit B shows the member status and the SD-WAN rule
configuration.
Based on the exhibits, which two statements are correct? (Choose two.)

• A. FortiGate updated the outgoing interface list on the rule so it prefers port2.
• B. Port2 has the highest member priority.
• C. SD-WAN rule ID 1 is set to lowest cost (SLA) mode.
• D. Port2 has a lower latency than port1.

Answer: A,D

NEW QUESTION # 35
Refer to the exhibit, which shows an SD-WAN zone configuration on the FortiGate GUI.

Based on the exhibit, which statement is true?

• A. The overlay zone contains four members.
• B. You can delete the virtual-wan-link zone because it contains no member.
• C. You can move port1 from the underlay zone to the overlay zone.
• D. The corporate zone contains no member.

Answer: D

Explanation:
Based on the exhibit, the "corporate" zone contains no member (B). In the FortiGate GUI, zones without members do not display any interfaces listed under them, which is the case for the corporate zone in the exhibit. References: This conclusion is based on standard Fortinet GUI interpretation and the operational logic of SD-WAN zones as per Fortinet's guidelines and user interface standards.

NEW QUESTION # 36
Exhibit.

The exhibit shows VPN event logs on FortiGate. In the output shown in the exhibit, which statement is true?

• A. The VPN tunnel T_MPLS_0 is a shortcut tunnel.
• B. The master tunnel T_INET_0 cannot accept the ADVPN shortcut.
• C. There are no IPsec tunnel statistics log messages for ADVPN cuts.
• D. There is one shortcut tunnel built from master tunnel T_MPLS_0.

Answer: D

Explanation:
VPN event logs record the status of VPN tunnels, such as the establishment, termination, or failure of a tunnel. The output includes the following information:
logid: the log ID number
type: the log type, either traffic or event
subtype: the log subtype, either vpn or ipsec
level: the log level, either error, warning, or notice
vd: the virtual domain name
logdesc: the log description
msg: the log message
action: the log action, such as tunnel-up, tunnel-down, or tunnel-stats remip: the remote IP address locip: the local IP address remport: the remote port number locport: the local port number outintf: the outgoing interface name cookies: the IKE SA cookies user: the user name group: the user group name useralt: the alternative user name xauthuser: the XAuth user name authgroup: the XAuth user group name assignip: the assigned IP address vpntunnel: the VPN tunnel name tunnellip: the tunnel loopback IP address tunnelid: the tunnel ID number tunneltype: the tunnel type, either ipsec or ssl duration: the tunnel duration in seconds sentbyte: the number of bytes sent rcvdbyte: the number of bytes received nextstat: the next statistics interval in seconds advpnsc: the ADVPN shortcut flag, either 0 or 1 Based on the exhibit, the following statement is true:
There is one shortcut tunnel built from master tunnel T_MPLS_0. This means that the VPN tunnel T_MPLS_0 is a master tunnel that can send ADVPN shortcut offers to other spokes, and the VPN tunnel T_MPLS_0_0 is a shortcut tunnel that is built from the master tunnel T_MPLS_01. In the exhibit, the log action for T_MPLS_0 is tunnel-up, and the log action for T_MPLS_0_0 is shortcut-up. The advpnsc flag for T_MPLS_0 is 0, indicating that it is not a shortcut tunnel, while the advpnsc flag for T_MPLS_0_0 is 1, indicating that it is a shortcut tunnel.

NEW QUESTION # 37
Refer to the exhibit.

Which statement explains the output shown in the exhibit?

• A. FortiGate must re-evaluate the session due to routing change.
• B. FortiGate performed standard FIB routing on the session.
• C. FortiGate used192.2.0.1as the gateway for the original direction of the traffic.
• D. FortiGate will not re-evaluate the session following a firewall policy change.

Answer: A

Explanation:
The snat-route-change option is enabled by default. This option enables FortiGate to re-evaluate the routing table and select a new egress interface if the next hop IP address changes. This option only applies to sessions in the dirty state. Sessions in the log state are not affected by routing changes.

NEW QUESTION # 38
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows the SD-WAN performance SLA configuration, the SD-WAN rule configuration, and the application IDs of Facebook and YouTube. Exhibit B shows the firewall policy configuration and the underlay zone status.
Based on the exhibits, which two statements are correct about the health and performance of port1 and port2?
(Choose two.)

• A. Non-TCP Facebook and YouTube traffic are not used for performance measurement.
• B. The performance is an average of the metrics measured for Facebook and YouTube traffic passing through the member.
• C. FortiGate identifies the member as dead when there is no Facebook and YouTube traffic passing through the member.
• D. FortiGate is unable to measure jitter and packet loss on Facebook and YouTube traffic.

Answer: A,B

Explanation:
Study Guide 7.2, pages 103 - 104. Another comment said "because without using application Control on the firewall policy, SDWAN can't work" but there is a app control "default" defined on config.

NEW QUESTION # 39
Refer to the exhibits.
Exhibit A

Exhibit B

Exhibit A shows the SD-WAN performance SLA configuration, the SD-WAN rule configuration, and the application IDs of Facebook and YouTube. Exhibit B shows the firewall policy configuration and the underlay zone status.
Based on the exhibits, which two statements are correct about the health and performance of port1 and port2?
(Choose two.)

• A. Non-TCP Facebook and YouTube traffic are not used for performance measurement.
• B. The performance is an average of the metrics measured for Facebook and YouTube traffic passing through the member.
• C. FortiGate identifies the member as dead when there is no Facebook and YouTube traffic passing through the member.
• D. FortiGate is unable to measure jitter and packet loss on Facebook and YouTube traffic.

Answer: A,B

Explanation:
Study Guide 7.2, pages 103 - 104. Another comment said "because without using application Control on the firewall policy, SDWAN can't work" but there is a app control "default" defined on config.

NEW QUESTION # 40
Refer to the exhibit.

Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2. The administrator configured ADVPN on both hub-and-spoke groups.
Which two outcomes are expected if a user in Toronto sends traffic to London? (Choose two.)

• A. Toronto needs to establish a site-to-site tunnel with Hub 2 to bypass Hub 1.
• B. Traffic from Toronto to London triggers the dynamic negotiation of a direct site-to-site VPN.
• C. The first packets from Toronto to London are routed through Hub 1 then to Hub 2.
• D. London generates an IKE information message that contains the Toronto public IP address.

Answer: B,C

NEW QUESTION # 41
Which two performance SLA protocols enable you to verify that the server response contains a specific value? (Choose two.)

• A. dns
• B. twamp
• C. icmp
• D. http

Answer: A,D

NEW QUESTION # 42
Which components make up the secure SD-WAN solution?

• A. FortiGate, FortiManager, FortiAnalyzer, and FortiDeploy
• B. Datacenter, branch offices, and public cloud
• C. Telephone, ISDN, and telecom network.
• D. Application, antivirus, and URL, and SSL inspection

Answer: A

NEW QUESTION # 43
Which two statements about SD-WAN central management are true? (Choose two.)

• A. It uses templates to configure SD-WAN on managed devices.
• B. The objects are saved in the ADOM common object database.
• C. It supports normalized interfaces for SD-WAN member configuration.
• D. It does not support meta fields.

Answer: A,B

Explanation:
Normalized interfaces are not supported for SD-WAN templates. You can create multiple SD-WAN zones and add interface members to the SD-WAN zones. You must bind the interface members by name to physical interfaces or VPN interfaces.https://docs.fortinet.com/document/fortigate/7.0.0/sd-wan-new-features/794804/new-sd-wan-template-

NEW QUESTION # 44
Refer to the exhibit.

Based on the output shown in the exhibit, which two criteria on the SD-WAN member configuration can be used to select an outgoing interface in an SD-WAN rule? (Choose two.)

• A. Set cost 15.
• B. Set load-balance-mode source-ip-ip-based.
• C. Set priority 10.
• D. Set source 100.64.1.1.

Answer: A,C

NEW QUESTION # 45
Refer to the exhibit.

The device exchanges routes using IBGP.
Which two statements are correct about the IBGP configuration and routing information on the device? (Choose two.)

• A. You can run the get router info routing-table database command to display the additional paths.
• B. ibgp-multipath is disabled.
• C. additional-path is enabled.
• D. Each BGP route is three hops away from the destination.

Answer: A,C

NEW QUESTION # 46
......

Fortinet NSE7_SDW-7.2 Exam Syllabus Topics:

Topic	Details
Topic 1	SD-WAN Troubleshooting: Troubleshooting SD-WAN issues, including rules, routing, and ADVPN, is vital for maintaining network reliability. This section of the Fortinet NSE 7 - SD-WAN 7.2 exam tests the ability to diagnose and resolve SD-WAN problems using diagnostic commands and monitoring tools, ensuring robust and uninterrupted network operations.
Topic 2	Rules and Routing: Understanding SD-WAN Rules and Routing is crucial for directing traffic effectively. This topic of the NSE7_SDW-7.2 exam evaluates the capabilities of Fortinet network and security professionals to configure SD-WAN rules and routing.
Topic 3	SD-WAN Overlay Design and Best Practices: It focuses on the deployment of hub-and-spoke IPsec topologies and configuring ADVPN. Proficiency in this topic ensures that Fortinet network and security professionals can implement effective and reliable SD-WAN overlays tailored to organizational needs.
Topic 4	SD-WAN Configuration: This topic assesses skills of Fortinet network and security professionals in setting up basic SD-WAN environments, including configuring Direct Internet Access (DIA), SD-WAN Members, and Performance Service Level Agreements (SLAs). Proficiency here ensures the ability to design efficient and resilient SD-WAN configurations.
Topic 5	Centralized Management: This area focuses on deploying and managing SD-WAN through FortiManager, including using IPsec templates and SD-WAN Overlay Templates. Mastery here demonstrates the abilities of Fortinet network and security professionals to streamline SD-WAN configuration, enhance security, and maintain consistent policies across multiple sites.

 

Accurate & Verified 2024 New NSE7_SDW-7.2 Answers As Experienced in the Actual Test!: https://examboost.vce4dumps.com/NSE7_SDW-7.2-latest-dumps.html