Use EMC D-PDC-DY-23 Dumps To Succeed Instantly in D-PDC-DY-23 Exam
Ultimate Guide to D-PDC-DY-23 Dumps - Enhance Your Future Career Now
NEW QUESTION # 96
What must be done before configuring any routing protocol in a VRF instance?
- A. Assign each VRF instance to a routing group
- B. Nothing, VRF routing protocols are assigned automatically
- C. Create a routing group for each VRF instance
- D. Assign an IP address to at least one of the interfaces assigned to the VRF instance
Answer: D
NEW QUESTION # 97
To which IEEE standard are dynamic LAGs compliant on Dell EMC Networking OS10 switches?
- A. 802.3af
- B. 802.3ad
- C. 802.3ae
- D. 802.3ac
Answer: B
NEW QUESTION # 98
When implementing automation, which rationale should be considered?
- A. Enable the network to be managed as a single fabric.
- B. Automate corrective loop actions.
- C. Provide workflow for system administrators.
- D. Simplify the network topology.
Answer: A
NEW QUESTION # 99
When installing OS10 on a switch from a USB drive, what format is used for the file system?
- A. NTFS
- B. HFS+
- C. HFS
- D. FAT32
Answer: D
NEW QUESTION # 100
The network administrator wants to configure RADIUS authentication for VTY access, and for console access to use the local configuration.
Which two commands should be used to achieve this goal?
- A. aaa authentication login vty radiusaaa authentication login console group local
- B. aaa authentication login default group radius aaa authentication login console local
- C. aaa authentication login vty group radius aaa authentication login console local
- D. aaa authentication login default group radius aaa authentication login console group local
Answer: B
NEW QUESTION # 101
Which OS10 configuration will result in successfully assigning an IP address to interface 1/1/3, a 10G Ethernet interface?
- A. S3(config)# interface ethernet 1/1/3
S3(conf-if-eth1/1/3)# ip address 144.254.33.1/24
S3(conf-if-eth1/1/3)# no switchport - B. S3(config)# interface ethernet 1/1/3
S3(conf-if-eth1/1/3)# ip address 144.254.33.1/24
S3(conf-if-eth1/1/3)# no shutdown - C. S3(config)# interface ethernet 1/1/3
S3(conf-if-eth1/1/3)# no switchport
S3(conf-if-eth1/1/3)# ip address 144.254.33.1/24 - D. S3(config)# interface tengigabitethernet 1/1/3
S3(conf-if-eth1/1/3)# ip address 144.254.33.1/24
S3(conf-if-eth1/1/3)# no shutdown
Answer: C
NEW QUESTION # 102
A network administrator must restrict packets that are destined to the CPU of an OS10 switch.
How do they accomplish this?
- A. Control-plane ACLs
- B. Management-plane ACLs
- C. IP fragment ACLs
- D. Static null routes
Answer: A
NEW QUESTION # 103
Refer to the exhibit.
Which configuration will allow S1 to ping S2's Lo0 address?
- A. S1(config)# ip route 192.168.32.2 144.254.32.1/32
- B. S1(config)# ip route 144.254.32.1/32 192.168.32.2
- C. S1(config-router)# ip route 144.254.32.1 192.168.32.2/32
- D. S1(config-router)# ip route 192.168.32.2 144.254.32.1/32
Answer: B
NEW QUESTION # 104
What is one of the configuration requirements for VLT on OS10?
- A. Configure a time interval to delay bringing up VLT ports after reload when the VLTi is turned on after failure.
- B. Create a VLT domain on each peer using the vlt-domain command.
- C. Manually reconfigure the VLT MAC address. Configure the VLT MAC address on both VLT peers.
- D. Configure a port channel for VLTi
Answer: B
NEW QUESTION # 105
Which command is used to determine the VLT peer unit address?
- A. show vlt <Domain ID> detail
- B. show vlt <Domain ID> role
- C. show vlt <Domain ID>
- D. show running configuration vlt
Answer: A
NEW QUESTION # 106
Which user role in OS10 has full access to all commands and exclusive access to commands that manipulate the file system?
- A. secadmin
- B. sysadmin
- C. netadmin
- D. netoperator
Answer: B
NEW QUESTION # 107
What is a valid RADIUS Authentication command?
- A. OS10(config)# radius-server timeout never
- B. OS10(config)# radius-server retransmit 10
- C. OS10(config)# radius-server timeout 1500
- D. OS10(config)# radius-server retransmit 150
Answer: B
NEW QUESTION # 108
What is the range of values that can be used when using the vlt-port-channel command?
- A. 1-1024
- B. 1-512
- C. 1-128
- D. 1-256
Answer: A
NEW QUESTION # 109
An administrator has created a layer three trust-map and wants to verify that the priorities are associated with the correct group.
Which command shows the required data?
- A. OS10# show dscp maps type trust-map-type3 L3-trust-map
- B. OS10# show qos maps type trust-map-dot1p L3-trust-map
- C. OS10# show cos maps type trust-map-dot1p L3-trust-map
- D. OS10# show qos maps type trust-map-dscp L3-trust-map
Answer: D
NEW QUESTION # 110
What do bridge protocol data units provide?
- A. Configuration data exchanged during a VLTi setup
- B. Special data frames to exchange STP information
- C. Metadata transferred connecting two network bridges
- D. Bridge information part of the LLDP protocol
Answer: B
NEW QUESTION # 111
A company wants to document the steps that are needed for their upcoming deployment that are required to configure a single logical L2 domain from the perspective of attached devices that are terminating on separate nodes.
What three steps are recommended to meet these requirements? (Select 3)
- A. Configure VLT port channel.
- B. Create a virtual router.
- C. Configure the discovery-interface.
- D. Configure the VLT heartbeat.
- E. Configure virtual IP addresses.
Answer: A,D,E
NEW QUESTION # 112
ACL's have which two (2) actions?
- A. Modify or drop
- B. Forward or erase
- C. Redistribute or forward
- D. Permit or deny
Answer: D
NEW QUESTION # 113
What OS10 command is used to remove VLAN 40 from a trunk port?
- A. no switchport trunk allowed vlan 40
- B. switch pert mode trunk no allow vlan 40
- C. no switchport mode trunk
- D. switchport trunk delete vlan 40
Answer: A
NEW QUESTION # 114
An administrator is implementing VLT in OS10.
How should the administrator configure the VLTi port channel?
- A. Create port channel 1000 and assign as peer-link.
- B. A port channel is created automatically during VLT discovery.
- C. A port channel is created automatically during LLDP discovery.
- D. Create a LACP trunk with spanning tree disabled.
Answer: A
NEW QUESTION # 115
Two Dell Networking OS10 switches in a VLT configuration must be upgraded.
How will the reload of these switches proceed to result in the default initial state?
- A. Reload the primary VLT node and wait for it to join as secondary.
Wait until after delay restore timer has expired.
Reload VLT secondary node and wait for it to join as secondary. - B. Reload the primary VLT node and wait for it to join as primary.
Wait until after delay restore timer has expired.
Reload VLT secondary node and wait for it to join as secondary. - C. Reload the primary VLT node.
This process will automatically trigger the reload of the secondary node after it has recovered. - D. Reload the primary VLT node.
This will automatically trigger the simultaneous reload of the secondary node.
Answer: A
NEW QUESTION # 116
What are mandatory LLDPDU TLV's?
- A. 0123
- B. 0124
- C. 0
- D. 0456
Answer: A
NEW QUESTION # 117
Which command is used to create a non-default VRF instance?
- A. interface ethernet 1/1/1
- B. ip vrf forwarding vrf-test
- C. ip vrf
- D. ip vrf forwarding new-vrf
Answer: C
NEW QUESTION # 118
Which LSA type contains information about routes redistributed into OSPF?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 119
In a Layer 3 Leaf-Spine topology what can be used to move Layer 2 traffic between racks?
- A. VXLAN
- B. Port channel
- C. VLT
- D. Trunks
Answer: A
NEW QUESTION # 120
Refer to the exhibit:
A default route exists on OS10-C that points all Internet traffic towards 10.0.13.3 on OS10-B. A network administrator must re-route Internet traffic that is only sourced from Host-1 to 10.0.12.2 on OS10-A instead.
What feature can the administrator implement to accomplish this goal?
- A. OSPF Cost Manipulation
- B. Source-Based Routing
- C. Policy-Based Routing
Answer: A
NEW QUESTION # 121
......
EMC Dumps - Learn How To Deal With The Exam Anxiety: https://examboost.vce4dumps.com/D-PDC-DY-23-latest-dumps.html