[Jan 06, 2022] Latest Nutanix SE Academy NCSC-Level-1 Actual Free Exam Questions

Nutanix SE Academy NCSC-Level-1 Dumps Updated Practice Test and 80 unique questions

NEW QUESTION 41
Where in the Support Portal is the Best Practices guide for vSphere Networking located?

• A. Knowledge Base
• B. Product Notices
• C. Software Documentation
• D. Solutions Documentation

Answer: D

 

NEW QUESTION 42
A consultant is deploying a two-node cluster at a remote branch office.
Which component must be available to complete cluster configuration?

• A. Protection Domain
• B. Witness VM
• C. Remote Site
• D. Prism Central

Answer: B

 

NEW QUESTION 43
A consultant is using the Foundation applet to create a cluster. During the process the consultant refreshes the progress bar web page and is concerned when nothing loads.
What should the consultant do to verify that Foundation has completed successfully?

• A. Connect to any CVM IP address from a web browser.
• B. Restart the Foundation process.
• C. Update Java on the Foundation VM.
• D. Return to the Foundation configuration page and start over.

Answer: A

 

NEW QUESTION 44
A consultant is planning a new cluster installation and needs to locate the Shared IPMI port for each of the specific nodes that the customer has bought.
Which Support Portal location contains the document that would identify the port?

• A. Knowledge Base
• B. Solutions Documentation
• C. Software Documentation
• D. Hardware Replacement Documentation

Answer: D

 

NEW QUESTION 45
A consultant needs to review a customer's switch port configuration to identify any issues. Other customer requirements are as follows:
* Leverage LACP
* Native VLAN will not be used
* Use Multiple Upstream switches
* Use VLANs 20-25 and 30
* LACP Fallback has been Enabled
* vPC or MLAG has been configured
What must be included in a configuration in order to meet these requirements?

• A. Native VLAN set to 30
  Ports Trunked to allow all necessary VLANs
• B. Native VLAN set to 30
  Ports in access mode to allow all necessary VLANs
• C. Native VLAN set to default
  Ports in access mode to allow all necessary VLANs
• D. Native VLAN set to default
  Ports trucked to allow all necessary VLANs

Answer: D

 

NEW QUESTION 46
A customer has an ESXi Cluster with two 10GbE NICs on each node with the following requirements:
* Solution must follow Nutanix Best Practices
* Network configuration should be redundant
* A vSphere Standard Switch must be utilized
Which load balancing method should be used?

• A. Route based on originating port ID
• B. Route based on source MAC hash
• C. Route based on physical NIC load
• D. Route based on IP hash

Answer: A

 

NEW QUESTION 47
A consultant is viewing an ESXi host via console without external network connectivity.
Which two IP addresses can be used to connect to the CVM (Choose two.)

• A. 192.168.5.2
• B. 192.168.5.1
• C. 192.168.5.254
• D. 192.168.5.253

Answer: A,C

 

NEW QUESTION 48
Where can a consultant find Nutanix Enablement Starter Packs (ESPs)?

• A. In the Partner Portal
• B. In the Nutanix .NEXT Community Forum
• C. In the Services section of the Nutanix website.
• D. In the Support Portal

Answer: A

 

NEW QUESTION 49
Which two components must be identified to validate that software compatibility requirements are met for Nutanix Cluster Installation? (Choose two.)

• A. Guest OS
• B. AOS
• C. Firmware
• D. Hypervisor

Answer: B,D

 

NEW QUESTION 50
A consultant is installing Nutanix AOS on Cisco UCS.
Which method should be used to install AOS on UCS hardware platforms?

• A. Foundation Central
• B. Foundation VM
• C. Foundation as a Service
• D. Foundation Applet

Answer: B

 

NEW QUESTION 51
A consultant successfully completes a Foundation using a flat switch. The consultant then works with the customer to move the cluster over to their production network. After the move, the CVMs and hypervisors can no longer communicate, which prevents the cluster from starting.
Which option should be used to resolve this issue?

• A. If the IPMI is in use, check that the IPMI can ping the default gateway over IPv6.
• B. Make sure that the IPMI and CVM VLAN is manually tagged on the Host and CVM.
• C. Verify that IPv6 Link Local and DHCP is enabled on all switch ports.
• D. If using VLANs, confirm the hypervisor/CVM VLAN is set as Native on the switch ports.

Answer: D

 

NEW QUESTION 52
A consultant is setting up a new Hyper-V cluster. The customer requirements are as follows:
* VMs should automatically failover to another host if the host crashes
* Host CPU and Memory resources should be evenly balanced
* New VMs should be placed on the host with the most resources available Which two Hyper-V features can be used to meet the requirements? (Choose two.)

• A. High Availability
• B. Performance Resource Optimization
• C. Failover Clustering
• D. Distributed Resource Scheduler

Answer: B,C

 

NEW QUESTION 53
After a consultant runs Foundation, the imaging process fails.
In which two locations can the consultant find the logs? (Choose two.)

• A. On the CVM - /home/Nutanix/foundation/logs
• B. On the Foundation VM - /home/nutanix/foundation/logs
• C. Logs link on the Foundation Imaging Screen
• D. On the Hypervisor - /home/nutanix/foundation/logs

Answer: B,C

 

NEW QUESTION 54
A consultant is unable to install virtualization software on a laptop.
Which two versions of Foundation can be used to resolve this issue? (Choose two.)

• A. Foundation Central
• B. Foundation Portable
• C. Foundation Applet
• D. Foundation VM

Answer: B,C

 

NEW QUESTION 55
A consultant successfully installs the Foundation VM on a laptop and needs to ensure the VM can communicate externally.
Which two configuration changes should the consultant make next? (Choose two.)

• A. Configure the static IP address through the desktop virtualization software.
• B. Ensure the vNIC is set to bridged adapter.
• C. Run the set_foundation_ip_address application on the VM desktop.
• D. Open terminal and configure via ifconfig command.

Answer: B,C

 

NEW QUESTION 56
After a recent installation using a flat switch, a consultant notices issues migrating the Nutanix nodes to the customer's network. The customer states that they are using VLANs on the production switch but not on the dedicated switch for IPMI. The customer does not require a manual configuration of the host and CVM.
What network changes need to be made to correct the issues?

• A. Use Native VLANs for the CVM and host and trunk mode for IPMI.
• B. Use tagged VLANs for the CVM and host and access mode for IPMI.
• C. Use Native VLANs for the CVM and host and access mode for IPMI.
• D. Us untagged VLANs for the CVM and host and trunk mode for IPMI.

Answer: C

 

NEW QUESTION 57
......

Verified NCSC-Level-1 dumps Q&As - 100% Pass from VCE4Dumps: https://examboost.vce4dumps.com/NCSC-Level-1-latest-dumps.html